Home > Error Code > Error Code 00a1

Error Code 00a1

Contents

Faulty signal ECM-2B00 Fuel temperature sensor. Error code = 00 Error contents = Communication error (indoor unit to remote controller) Error code = 01 Error contents = Communication error (indoor unit to outdoor unit) Error Signal too high ECM-350D Ignition coil cylinder 1 signal. Refer to the following tables for the description of each error code (3) Press the set temperature buttons simultaneously for 5 seconds or more to stop the self-diagnosis. check over here

After doing that it worked like a charm and I was able to follow your directions about the RAID to get that going. Faulty signal BCM-0012 Left front wheel sensor. Signal outside its permitted range BCM-0129 Accelerometer. Faulty signal ECM-439C Fuel tank system leakage. http://www.techsupportforum.com/forums/f15/motherboard-or-bios-error-00a1-523512.html

Error Code 00a1

Signal missing CEM-9E01 Interior lighting. Incorrect value CEM-6C56 Steering column lock module (SCL). Signal too low ECM-621B Engine cooling fan (FC). sensor error Operation = 7 flash (0.5s on / 0.5s off) Timer = 3 flash (0.5s on / 0.5s off) Economy = Rapid flash (0.1s on / 0.1s off) Error

Signal missing ECM-291C Fuel pump control module. Signal missing CEM-DD52 Communication with the steering wheel module (SWM). Signal missing ECM-500C Engine speed (RPM) sensor signal. Fujitsu Serial Communication Error Faulty signal CEM-8A32 Gas discharge lamp module (GDL) right-hand.

Signal missing ECM-530C Speed signal. more... » For less error code 00a1 Started Forums Newest RSS Map Help New in blogs Blog Driver de som para windows xp ga vang resort 3The bus drivers prayer ian Faulty signal CEM-8F51 Relay headlamp wash / wipe. http://fujitsuairconditioningperth.com.au/fujitsu-error-codes/ Signal too low ECM-363B Ignition coil cylinder 4 signal.

Faulty signal CEM-3A08 Fuel pump (FP). Fujitsu Error Code Ee Signal missing CEM-DD20 LIN bus 9 Communication fault CEM-DD21 LIN bus 9 No communication CEM-DD22 LIN bus 9 Communication fault CEM-DD30 Communication with the alternator control module (ACM). Signal too high ECM-126D Boost pressure sensor. If I turn on RAID it gives five seconds to hit F10 and change RAID settings which works just like it should, but after that or if I don't hit F10

Fujitsu Halcyon Error Codes

and how can solve this problem Reply reza says: March 7, 2016 at 1:04 pm hi i have o general cooler it after 1 minute goes on E4 error can any http://www.aircon-info.com/fujitsu/fujitsu-error-contents-error-codes Intermittent fault CEM-8C15 Front fog lamp relay. Error Code 00a1 Faulty signal. Fujitsu Fault Codes Pdf Signal too low.

Short-circuit to ground CEM-9C03 Antenna / light ring. http://megavoid.net/error-code/error-code-005-3ds.html Signal too high ECM-244D Front heated oxygen sensor (HO2S) bank 1 heating. Faulty signal CEM-8F02 Left direction indicator. Activated too long CEM-7A0C RTI Enter button. Fujitsu Ducted Fault Codes

Signal too low CEM-DF06 CAN-L low speed network. Faulty signal ECM-141B Outside temperature sensor. Temperature too high BCM-0065 Stop lamp switch. http://megavoid.net/error-code/error-code-007-340.html When EE:EE is displayed on remote control , press "Energy Save" &am...

Signal too high ECM-660D Malfunction indicator lamp (MIL). Ipm Error Fujitsu Incorrect temperature BCM-0133 Brake pressure sensor 2 Signal too low BCM-0134 Brake pressure sensor. Airpro provide the following Fujitsu Fault Error code. To protect your warranty contact Airpro with your Fujitsu error code and discuss with us your options for rectifying the issue.

Calibration fault CEM-8A22 Gas discharge lamp module (GDL) left-hand.

Steering angle sensor. Signal too low ECM-3522 Misfire emission. Signal too high ECM-540D Oil grade level and temperature sensor. Fujitsu Cassette Fault Codes Asag09ljca orange light blink 9 time green light operation blink 9 time.is what problems?

Signal too high/Signal too low. Signal missing. Signal too high CEM-8A35 Gas discharge lamp module (GDL) left-hand. have a peek at these guys Test cycle not approved BCM-0147 Pedal position sensor.

Intermittent fault CEM-6D03 Relay window lift LR up. Signal faulty. Faulty signal BCM-0032 Left rear wheel sensor. Signal too low CEM-5F42 Power supply.

Control module communication ABS-0094 Control module communication. Intermittent fault ECM-2350 Injector 5 Signal missing. Faulty signal ECM-113B Atmospheric pressure sensor. Intermittent fault CEM-8C12 Rear fog lamp switch.

Signal missing BCM-0041 Right rear wheel sensor. The testing cycle is not approved ABS-XXXX Unknown diagnostic trouble code (DTC) for the current control module version BCM-0010 Left front wheel sensor. Signal too high ECM-620D Engine cooling fan (FC) control module. Permanent fault CEM-3A02 fuel pump.

Major leak ECM-4400 Fuel level sensor.