Home > Error Cannot > Error Cannot Parse Routing-option Max-interface-supported

Error Cannot Parse Routing-option Max-interface-supported

Contents

While the new stack master is being elected and is resetting, the switch stack does not forward IPv6 packets. Beginning in privileged EXEC mode, follow these steps to configure an IPv6 static route: Command Purpose Step 1 configure terminal Enter global configuration mode. Configuring Static Routes for IPv6 Before configuring a static IPv6 route, you must enable routing by using the ip routing global configuration command, enable the forwarding of IPv6 packets by using vlan —Maximize VLAN configuration on the switch with no routing supported in hardware. his comment is here

Step 2 ipv6 dhcp pool poolname Enter DHCP pool configuration mode, and define the name for the IPv6 DHCP pool. not-advertise —(Optional) Set the address range status to DoNotAdvertise. Table 39-2 shows the privileged EXEC commands for monitoring IPv6 on the switch. In addition to the normal SPAN and RSPAN limitations defined in the software configuration guide, these limitations are specific to IPv6 packets: – When you send RSPAN IPv6-routed packets, the source https://kb.juniper.net/KB20977

Error Cannot Parse Routing-option Max-interface-supported

HTTP relies on the TCP/IP stack and the sockets for processing network-layer interactions. routing —Set the switch to the routing template to support IPv4 and IPv6 routing, including IPv4 policy-based routing. Step 3 ipv6 address dhcp [ rapid-commit ] Enable the interface to acquire an IPv6 address from the DHCPv6 server. Before configuring DHCPv6, you must select a Switch Database Management (SDM) template that supports IPv4 and IPv6.

A slash mark must precede the decimal value. Output from the show ipv6 interface EXEC command shows how the interface ID (20B:46FF:FE2F:D940) is appended to the link-local prefix FE80::/64 of the interface. A host autonomously configures its own link-local address, and booting nodes send router solicitations to request router advertisements for configuring interfaces. You can optionally specify the IPv6 address of the next hop to which packets are sent.

cost cost —(Optional) Metric or cost for this summary route, which is used during OSPF SPF calculation to determine the shortest paths to the destination. EIGRP IPv6 does not need to be configured on a passive interface. Step 5 configure terminal Enter global configuration mode after the switch reloads. Go Here These messages are multicast periodically or are solicited by hosts.

The DNS AAAA resource record types support IPv6 addresses and are equivalent to an A address record in IPv4. Step 10 copy running-config startup-config (Optional) Save your entries in the configuration file. You must configure an IPv6 address and IPv6 processing on an interface by using the ipv6 address interface configuration command. To disable an OSPF routing process, use the no ipv6 router ospf process-id global configuration command.

GNS VIRL IOU Rack Rentals Unified Networking Lab View Results Loading ... Step 4 link-address IPv6-prefix (Optional) Specify a link-address IPv6 prefix. Error Cannot Parse Routing-option Max-interface-supported It is configured on the interfaces on which it runs and does not require a global IPv6 address. ipv6-prefix— The IPv6 network that is the destination of the static route.

super.. The switch does not support the Route Information Option in RFC 4191. A decimal value that shows how many of the high-order contiguous bits of the address comprise the prefix (the network portion of the address). In IPv6, ICMP packets are also used in the neighbor discovery protocol and path MTU discovery.

The stack master also runs all IPv6 applications. Notas estudo JNCIA-Junos parte 1 Estas são as minhas notas de estudo para o exame... To configure a floating static route, use an administrative distance greater than that of the dynamic routing protocol. weblink The IPv6 address space reduces the need for private addresses and Network Address Translation (NAT) processing by border routers at network edges.

IPv6 hosts learn of available routers through IPv6 neighbor discovery router advertisement messages. This example shows how to enable the RIP routing process cisco with a maximum of eight equal-cost routes and to enable it on an interface: Switch(config)# ipv6 router rip cisco Switch(config-router)# To globally disable IPv6 routing, use the no ipv6 unicast-routing global configuration command.

Note This procedure is the minimum number of steps required to enable HSRP for IPv6.

preference value —(Optional) The preference value carried in the preference option in the advertise message sent by the server. Step 4 end Return to privileged EXEC mode. To delete a DHCPv6 pool, use the no ipv6 dhcp pool poolname global configuration command. The range is 1 to 4294967295.

The highest number represents the highest priority. Configuring Default Router Preference Router advertisement messages are sent with the default router preference (DRP) configured by the ipv6 nd router-preference interface configuration command. instance instance-id— (Optional) Instance identifier. check over here For more information about IPv4 and IPv6 protocol stacks, see the “Implementing IPv6 Addressing and Basic Connectivity” chapter of Cisco IOS IPv6 Configuration Library on Cisco.com.

Step 4 end Return to privileged EXEC mode. It does not support site-local unicast addresses. For information about syslog over IPv6, including configuration procedures, see the “Implementing IPv6 Addressing and Basic Connectivity” chapter in the Cisco IOS IPv6 Configuration Library on Cisco.com. Step 9 show ipv6 ospf [ process-id ] [ area-id ] interface [ interface-id ] or show ipv6 ospf [ process-id ] [ area-id ] Display information about OSPF interfaces.

Step 3 end Return to privileged EXEC mode. For more information about configuring OSPF routing for IPv6, see the “Implementing OSPF for IPv6” chapter in the Cisco IOS IPv6 Configuration Library on Cisco.com. Step 2 ipv6 route ipv6-prefix/prefix length { ipv6-address | interface-id [ ipv6-address ]} [ administrative distance ] Configure a static IPv6 route. only —Select to originate the default route, but suppress all other routes in the updates sent on this interface.